This card can insert several data values in the VBI of the outputs. With the following settings you can choose what you want to insert.
SMPTE ST 352 Payload Identifier
The SMPTE ST 352 Video Payload Identifier, also known as VPID, is transported within the ancillary data of an SDI stream. The ancillary packet is placed in the HANC space. This packet contains 4 bytes of data.
There are two versions of the standard. The first was published in 2011 and the second in 2013. The revision can be seen within the 4 bytes.
When the 2GF100 is not processing the incoming VPID packets, they will be passed transparently. When it generates the packets, the 2GF100 will output VPID packets using the 2013 standard.
| Setting | Description | ||
| S352_Insert | S352_Insert enables the Video Payload Identifier insertion in the HANC space. It enables the user to insert or passthrough (On) the S352 Dynamic range and colorspace payload. When this menu item is set to On (default), it will generate a SMPTE ST352-2013 packet and overwrite the existing one (for both Luminance and Chrominance).When it is set to Off, it will pass the packet to the output as-is (only on Luminance).In HD 1080i for ATC-LTC transparency, the user may switch it Off to pass the ATC-LTC HANC packet on line 10. | ||
| Output-Matrix |
This setting will only work if S352_Insert is set to On. It enables you to set the colorspace in REC709 (default) or REC2020. When set to either REC709 or REC2020, the S352 data is included in the s352 packet. (This does not change anything in the picture.) |
||
| HDR_Curve_Out |
The dynamic range is the range of information between the lightest and darkest part of an image, also known as an image’s luminosity. This setting enables you to set the dynamic range in standard dynamic range SDR (default), HLG, PQ or SLOG3. With all of these settings, the S352 data is included in the S352 packet. (This does not change anything in the picture.) |
||
| Bit_Depth_Out |
Bit depth is the range of bits being used. This setting enables you to set the bit depth to Narrow (8bits) or Full (10bits). When set to either Narrow (default) or Full, it includes this data in the S352 packet. (This does not change anything in the picture.) |
||
| S2016-Line | With this setting you select a line in the VBI to where the AFD (SMPTE 2016) data should be written. Lines 0 till 31 are selectable. By default it is set to line 17. | ||
| Timecode_ins |
Here you can set if the timecode on the inputs should be copied to the outputs (On), or to copy the timecode from input 1 to input 2 (Copy 1 => 2), or to copy the timecode from input 2 to input 1 (Copy 2 => 1). You can also turn Off timecode insertion. Default is On. |
||
| VITC_Ln_In | With this setting you can select what line of the input you want to copy the VITC data from (only when input is SD). Can be any line between line 7 and line 22. Default is line 19. | ||
| VITC_Ln_Ctrl | Here you can choose whether you want to select the line, to where you want to copy the timecode data to, manually (manual) or use the information in the ATC_DBB package to select the lines (ATC_DBB package contains information about the line duplication as well). Default is Manual. | ||
| VITC_Ln_625 | When VITC_Ln_Ctrl is set to Manual, with this setting you can select a line between 7 and 22 when the output is SD625. Default is line 19. | ||
| VITC_Ln_525 | When VITC_Ln_Ctrl is set to Manual, with this setting you can select a line between 7 and 22 when the output is SD525. Default is line 10. | ||
| VITC_Ln_Dup | When set to On, the VITC line is duplicated to the above selected line + 2 lines. | ||
| Ins_CtrlA | With this item you select how the inserter presets are controlled: Manually (manual), via GPI-triggers (GPI-A, GPI-B or GPI-C), via changes of the SD aspect ratio (SD_AR) or the HD aspect ratio (S2016). Default is Manual. | ||
| Ins_Prst_ActA | With this item you can manually change the currently active preset of Channel A when in transparent mode. Can be any preset between 1 and 16. By default it is set to 1. All menu settings that are preceded with a ‘#Ins’-prefix are part of the preset. | ||
| Ins_Prst_EditA | Here you can select which of the 16 selectable presets you want to edit when in a transparent mode. Changing this will not change the active preset, unless the currently active preset is the same you are going to edit. All menu settings that are preceded with a ‘#Ins’-prefix are part of the preset. | ||
| #VI-InsertA | You can turn VI insertion on or off for Channel A. Default is Off. | ||
| #VI-DataA |
With the #VI-InsertA setting set to On, you can select VI values with this setting, which you want to be inserted. possible are all VI values from 4:3_0 through 4:3_7 and the settings from 16:9_0 through 16:9_7. Default is 4:3_0. |
||
| #WSS-InsertA | You can choose which type of WSS data you want to insert with this setting, or switch WSS insertion entirely off (default value). You can set it to Standard or Extended. | ||
|
|||
| #WSS-StndA | With the #WSS-InsertA setting set to Standard, you can select WSS standard values with this setting, which you want to be inserted. possible are all WSS values from 1_vid through 8_vid and the settings from 1_flm through 8_flm. Default is 1_vid. | ||
| #WSS-ExtndA | With the #VI-InsertA setting set to Extended, you can select VI values with this setting, which you want to be inserted. Possible WSS values are 4:3_0 through 4:3_7 and the settings 16:9_0 through 16:9_7. Default is 4:3_0. | ||
| #S2016-InsertA | You can turn S2016 (AFD) insertion on or off for Channel A. Default is Off. | ||
| #S2016-DataA | With the #S2016-InsertA setting set to on, you can select AFD values with this setting, which you want to be inserted. possible are all AFD values from AFD0 through AFD15. | ||
| #OSD-StyleA |
With this setting you select how the on-screen display text should be displayed. Possible are: Off (no OSD) Transp (transparent text) Masked (OSD displayed in a black box) Blink-Transp (blinking transparent text) Blink-Masked (blinking text in a black box) |
||
| #OSD-TextA | Here you can set a 10-character long text which should be displayed on-screen when the above setting is not set to Off. | ||
| Ins_CtrlB | With this item you select how the inserter presets for Channel A are controlled: Manually (manual), via GPI-triggers (GPI), via changes of the HD Aspect Ratio (VI, WSS, WSS-ext or S2016 (AFD)). Default is Manual. | ||
| Ins_Prst_ActB | With this item you can manually change the currently active preset of Channel B when in transparent mode. Can be any preset between 1 and 16. By default it is set to 1. All menu settings that are preceded with a #Ins-prefix are part of the preset. | ||
| Ins_Prst_EditB | Here you can select which of the 16 selectable presets you want to edit for Channel B when in a transparent mode. Changing this will not change the active preset, unless the currently active preset is the same you are going to edit. All menu settings that are preceded with a #Ins-prefix are part of the preset. | ||
| #VI-InsertB | You can turn VI insertion on or off for channel B. Default is Off. | ||
| #VI-DataB | With the #VI-InsertB setting set to on, you can select VI values with this setting, which you want to be inserted in Channel B. All VI values are possible from 4:3_0 through 4:3_7 and the settings from 16:9_0 through 16:9_7. Default is 4:3_0. | ||
| #WSS-InsertB | You can choose which type of WSS data you want to insert in Channel B with this setting, or switch WSS insertion entirely off (default value). You can set it to Standard or Extended. | ||
|
|||
| #WSS-StndB | With the #WSS-InsertB setting set to Standard, you can select WSS standard values with this setting, which you want to be inserted in Channel B. possible are all WSS values from 1_vid through 8_vid and the settings from 1_flm through 8_flm. Default is 1_vid. | ||
| #WSS-ExtndB | With the #VI-InsertB setting set to on, you can select VI values with this setting, which you want to be inserted in Channel B. possible are all WSS values between 4:3_0 and 4:3_7 and the settings between 16:9_0 and 16:9_7. Default is 4:3_0. | ||
| #S2016-InsertB | You can turn S2016 (AFD) insertion on or off for Channel B. Default is Off. | ||
| #S2016-DataB | With the #S2016-InsertB setting set to on, you can select AFD values with this setting, which you want to be inserted in Channel B. possible are all AFD values from AFD0 through AFD15. | ||
| #OSD-StyleB |
With this setting you select how the on-screen display text should be displayed on outputs B. Possible are: Off (no OSD) Transp (transparent text) Masked (OSD displayed in a black box) Blink-Transp (blinking transparent text) Blink-Masked (blinking text in a black box) |
||
| #OSD-TextB | Here you can set a 10 character long text which should be displayed on-screen on outputs B when the above setting is not set to Off. | ||